Nylon "Bridge" by Taulman 3D

Nylon bridge filament from Taulman 3D.
£3.25

Product information

United States of America

Base Reference:
taulman 3D Printer Filament.  Starting with our strongest base polymer used for a percentage of nylon 645, we began working all of these requests.

Adherence to the Printing platform:
First, was the adherence to the Printing platform. Those that follow the use of nylon in posts, blogs and 3DP discussion rooms know of using garolite (LE) as a print surface. While this works well for all of taulman3D nylons, garolite is not always easy to acquire and even so, requires a properly cut section that fits each user's unit. Our thanks goes out to our chemical company for helping to change this requirement. The surface properties of most nylons is extremely slippery making adherence to the printing platform difficult. Our chemical company was able to make minor adjustments, to reduce the surface effect just slightly, thus allowing for the use of most PVA glues, either full strength or diluted. Initial testing shows that in some cases, the PVA was better with Bridge than garolite is with 618. Thus, some dilution was used. The specific PVA used in our labs is a very low cost "ELMER'S Glue-All" White PVA.

Reduced water up-take:
Next was Reduced water up-take from local humidity. While it is not possible to eliminate the water uptake by nylon, it is possible to localize it to the surface through final processing changes. Therefore when printing, rather than water creating a subtle popping that can effect the surface finish, Bridge will hold the water to the outer portion resulting in a slight steam when wet. The result of this is that Bridge needs little or no drying in the winter and just needs to be warmed in the summer months. This is a manufacturing process that our extrusion house developed and added to our existing taulman3D processes.

Reduced Shrinkage:
We found that the same process that reduces water uptake also helps to reduce shrinkage. While nylon will always have a slightly higher amount than ABS, we were able to reduce it to an in/in value less than our current nylons. These changes also led to a slight reduction in stringing as the extruded threads are a thicker melt.

Non-destructive evaluation:
Non-destructive evaluation of 3D Printed parts is a function of the transparency of Bridge. Like nylon 645, this transparency allows for visual inspection of printed parts. This is a combined request from our industrial and clinical customers. As noted early on, parts can be printed "too fast" for some polymers. While the outside of the part may look acceptable, a part printed too fast will not have internal fill material that actually adheres to the inside of the perimeter. With Bridge and nylon 645, Non-destructive evaluation is a simple visual verification.

Certified measure of strength:
With this combination of advancements, taulman3D proceeded with a limited test run. From this initial test run, we printed test samples to be sent out to the St Louis test labs. A fully accredited testing facility supporting the central US. The lab reported a Tensile Stress PSI of 4,800 for Bridge when 3D printed. 

You can purchase whole spools/reels/coils from these suppliers.

Asia - 
Australia -
Europe -
Middle East - 

United Kingdom - 3D FilaPrint
USA -

Note:  All filament weights include packaging. Average weight for 5 metres of 1.75mm filament (without packaging) is 15 gms and 5 metres of 3mm filament is 35 gms.

Samples are shipped in a clear resealable bag, with a small sachet of silica gel.


Manufacturer recommended printer temperatures.
Extrusion Temp:
Not available at time of posting
Platform Temp: Not available at time of posting
Platform Materials: Not available at time of posting

Please note, the above temperatures are only a guide.

Are you a filament manufacturer?  Would you like us to advertise and promote your filament here on GlobalFSD?  Then drop us a line and contact name and we will get back to you within 24 hours sales@globalfsd.com

Are you a filament reseller?  You can be one of just five resellers from each region or country, displayed on this product listing.  Contact sales@globalfsd.com for more information.

Technical Specifications

Brand Taulman 3D
Weight 0.065kg

Reviews

Write a review and share your thoughts with other shoppers!
No reviews yet, be the first.